聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
業內資訊
導致石材雕刻機出現錯位表象的原因是什么？
來源：http://m.yhuizhuanyao.com 時間：2020-12-04
石材雕刻機在雕刻過程中出現各種錯位缺點，如左右錯位、上下錯位、x軸錯位、z軸錯位等等，終究是什么緣由致使雕刻機出現錯位表象呢?
Stone engraving machine in the process of carving a variety of dislocation defects, such as left and right dislocation, up and down dislocation, X-axis dislocation, z-axis dislocation and so on. What causes the carving machine to appear dislocation appearance?
1.檢查雕刻軟件的途徑正確與否；
1. Check whether the way of engraving software is correct or not;
2.檢查絲桿的空地巨細及光桿的緊固螺絲有沒有松動；
2. Check the space size of the screw rod and whether the fastening screw of the polished rod is loose;
3.檢查軟件參數的設置正確與否；
3. Check whether the software parameters are set correctly;
4.檢查地線是不是接好；
4. Check whether the ground wire is well connected;
5.電腦是不是有病毒或許與其他不兼容或許煩擾，一般主張無須企業機簡略拼裝機箱即可；
5. Whether the computer has virus or not, it may be incompatible with other computers or annoyed. Generally speaking, it is not necessary to simply assemble the chassis of brand-name computers;
6.水冷主軸電機前上方的聯軸器，是不是松動損壞，可檢查用手擰緊或許替換；
6. If the coupling at the top and front of the water-cooled spindle motor is loose and damaged, it can be checked and replaced by hand;
7.雕刻機橫梁上到機器控制箱聯接拖鏈的線，是不是有接觸不良；
7. Whether there is poor contact between the line connecting the crossbeam of engraving machine and the drag chain of machine control box;
8.驅動器的疑問：驅動器本身里面的布局或許電子原器材有疑問，也會構成錯位表象，這個緣由比較多，若出現的次數不多，而且把速度下降一點，有時能正常雕刻，這說明驅動器還沒有徹底壞掉；若是一開始雕刻就錯位，就說明驅動器徹底壞了。處理方法：修補驅動器或許替換驅動器；
8. Questions about the driver: the layout of the drive itself may have doubts about the original electronic equipment, which may also constitute the appearance of dislocation. This is due to a lot of reasons. If the number of times is not too many, and the speed is reduced a little, sometimes it can carve normally, which indicates that the driver has not been completely damaged; if the engraving is misplaced at the beginning, the driver is completely broken. Treatment: repair the drive or replace the drive;
9.電壓的疑問：雕刻機在作業時需求的功率大，若是電壓過低，給驅動器供電缺少，功率達不到則會構成錯位表象，這種情況一般以Y軸錯位為多，出現這種表象有可能是外界電壓不可，或許在同一線路上有人使用了大功率的設備如電焊等。處理方法：裝置一個5000瓦的穩壓電源，但這個穩壓電源的過失規劃不能超過5%，建議在3%以內；
9. Question of voltage: the engraving machine needs high power during operation. If the voltage is too low, the power supply to the driver is insufficient, and the power can not reach it, it will form a dislocation image. In this case, Y-axis dislocation is more common. This appearance may be caused by external voltage. Maybe someone has used high-power equipment such as welding on the same line. Treatment method: install a 5000 Watt regulated power supply, but the fault planning of this regulated power supply should not exceed 5%, and it is recommended to be within 3%;
10.接口板，主板，轉接板的疑問：要是接口板，主板，轉接板壞了，雕刻機在作業的過程中，某一個方向或許是三個軸均不動，構成雕刻錯位；
10. Interface board, motherboard, adapter board questions: if the interface board, motherboard, adapter board are broken, engraving machine in the process of operation, a certain direction may be three axes are not moving, constitute carving dislocation;
主軸電機的疑問：要是步進電機或許是伺服電機的疑問，整個機器在某一方向上都不移動，用手轉絲桿也轉不動。
Spindle motor question: if the stepper motor may be a servo motor, the whole machine does not move in a certain direction, and the screw rod can not rotate by hand.
11.機床本身的疑問：機床上的某個部件有疑問或許是松動，表面有雜質等也會出現錯位表象;如聯軸器松了，壞了，都會出現錯位;導軌，絲桿上長期沒有清潔加油也會出現錯位表象；機床線要是斷了也會出現錯位表象。
11. Problems of the machine tool itself: some parts on the machine tool may be loose, and there are impurities on the surface. If the coupling is loose or broken, there will be dislocation; if the guide rail and screw rod have not been cleaned and oiled for a long time, the dislocation image will also appear; if the machine tool line is broken, it will also appear dislocation appearance.
- 上一篇：四工序開料機的主軸電機冷卻方式？
- 下一篇：石材雕刻機怎么選用質量好的石材
