tube老熟妇视频,天天插天天爱天天透,天天操天天日夜夜干

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

石材雕刻機的斷刀問題怎么解決？

來源：http://m.yhuizhuanyao.com 時間：2021-05-31

關于石材雕刻機在使用的時候，會時不時的出現斷刀的問題，這時候我們就要對出現斷刀的原因進行解決，這樣才能及時的止損，保障設備的正常運行。那么下面我們就來進行相關的了解吧。

When using the stone carving machine, there will be the problem of broken knife from time to time. At this time, we need to solve the cause of broken knife, so as to stop loss in time and ensure the normal operation of the equipment. Now let's have a related understanding.

1、考慮一下原材料是否有殘渣或者的強度是否過變大。長期手工雕刻高韌性的原材料，數控刀片的損壞和斷刃是難以避免的。像手工雕刻紅木，假如速率調的太大，那麼刀斷的必定的。

1. Consider whether there is residue in the raw material or whether the strength of the material is too high. Long term manual carving of high toughness raw materials, CNC blade damage and broken edge is inevitable. Like hand carved mahogany, if the speed adjustment is too large, then the knife must be broken.

2、石材雕刻機在長期工作時沒有拆換數控刀片，造成數控刀片自身在強度、抗壓強度、和鋒利度上受到非常大影響，可以常常查驗數控刀片是不是損壞了，如果發現損壞的程度比較大的話，那么我們就需要及時地進行更換。

2. Stone carving machine in the long-term work did not replace the numerical control blade, resulting in the numerical control blade itself in the strength, compressive strength, and sharpness are greatly affected, you can often check whether the numerical control blade is damaged, if the degree of damage is relatively large, then we need to replace it in time.

3、石材雕刻機數控車床是不是合適生產加工這類原材料，石材雕刻機數控車床放置是不是在水準表面，如果沒有準確的進行放置的話，也會導致刀具的斷裂。

3. Whether the CNC lathe of stone carving machine is suitable for the production and processing of such raw materials, whether the CNC lathe of stone carving machine is placed on the level surface, if it is not placed accurately, it will also lead to the fracture of the cutting tool.

4、伺服電機的轉速比是不是過低，伺服電機轉速比過低，每齒每轉吃走刀的量就增加，那樣切削速度就增加，就會造成刀斷，如果出現這種情況，就要及時地進行調解。

4. Is the speed ratio of the servo motor too low? If the speed ratio of the servo motor is too low, the amount of feed per tooth per revolution will increase, so the cutting speed will increase, which will cause the tool to break. If this happens, it is necessary to mediate in time.

5、數控刀片和夾頭頂是不是有塵土，筒夾里的塵土一定得清除整潔，不然那些的數控刀片全是非常容易斷的，上刀幅度是不是過大。筒夾和螺帽是否完好無損。這些都是需要我們考慮到的。

5. Whether there is dust on the NC blade and the top of the clip, the dust in the collet must be cleaned up, otherwise the NC blades are all very easy to break, and whether the loading range is too large. Whether the collet and nut are intact. All these need to be taken into consideration.

以上就是對于石材雕刻機出現問題，我們應該怎樣應對。如果還有不明白的地方，可以來華捷數控進行相關的咨詢和了解。

The above is for stone carving machine problems, we should how to deal with. If you still don't understand, you can come to Huajie CNC for relevant consultation and understanding.