聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
新聞資訊
有關雕刻機雕刻不夠圓潤的原因
來源：http://m.yhuizhuanyao.com 時間：2022-03-17
在實際的生產過程中，雕刻機雕刻的效果不一定能滿足客戶的要求，特別是如果效果不夠流暢，我們應該找出原因并及時處理。但在實際工作中,如果出現這種情況,主要有以下兩個原因:
In the actual production process, the engraving effect of the engraving machine may not meet the requirements of customers, especially if the effect is not smooth enough, we should find out the reason and deal with it in time. However, in practice, if this happens, there are two main reasons:
1、雕刻機的y軸或x軸可能同時有間隙，導致雕刻過程中抖動，雕刻路徑偏差，雕刻不順暢;
1. The y-axis or x-axis of the engraving machine may have a gap at the same time, resulting in jitter in the engraving process, deviation of engraving path and unsmooth engraving;
解決方案：改變直線或曲線的速度，改變數值由雕刻機本身的參數決定。
Solution: change the speed of straight line or curve, and the change value is determined by the parameters of the engraving machine itself.
2、雕刻機的線速度與曲線速度相差過大，導致雕刻機在走曲線時產生振動，這意味著雕刻路徑偏離，雕刻不平滑。
2. The difference between the linear speed of the engraving machine and the curve speed is too large, resulting in the vibration of the engraving machine when walking the curve, which means that the engraving path deviates and the engraving is not smooth.
解決方法：如果雕刻機是一個圓形導軌，找到一種方法來改變導軌或滑塊，動作會比較大，這取決于原因。如果它是一個正方形的軌道，它就簡單多了。只需調整上下滑塊或前后滑塊;
Solution: if the engraving machine is a circular guide rail, find a way to change the guide rail or slider, the action will be relatively large, depending on the reason. If it were a square orbit, it would be much simpler. Just adjust the upper and lower sliders or the front and rear sliders;
在使用過程中，濟南雕刻機出現雕刻不圓滑的現象是非常常見的，這就需要相關操作人員及時檢查原因，對癥下藥，解決問題，具體方法可以參考上述建議。如果還是無法解決問題，那就需要聯系廠家或者找維修人員進行檢修，不要盲目維修，以免對雕刻機造成二次傷害。
In the process of use, it is very common that the engraving of Jinan engraving machine is not smooth, which requires relevant operators to check the causes in time, suit the remedy to the case and solve the problems. For specific methods, please refer to the above suggestions. If you still can't solve the problem, you need to contact the manufacturer or find maintenance personnel for maintenance. Don't repair blindly to avoid secondary damage to the engraving machine.
以上就是為大家介紹的有關3050雕刻機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.yhuizhuanyao.com
The above is the detailed introduction of 3050 engraving machine. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://m.yhuizhuanyao.com//
- 上一篇：木工開料機生產過程中灰塵如何有效解決？
- 下一篇：開料機能提率的可行性方法有哪些？
